Warhammer 40k Space Wolves Wolfspear Squad Roles Jarl Custom A6 Transfer Sheet

Please read before purchase. These are printed using a Laser printer and may take quite a while to be ready due to how time consuming the process is and other orders before yours. I do not do rush orders and these are not the same quality as the sheet you get in a GW box, decal printing is not an exact process and there may be a few differences from the mock design such as the colour being different, white being slightly transparent and also sometimes a printed blur, colour shift or offset to the icons, I can't control this and they are minor issues so please bear in mind BEFORE you purchase. These are also not pre-cut icons like in a GW transfer box, you have to cut around the icon yourself on the clear film part so there is an edge to work with.I will not accept any cancellations for 'Won't arrive on time or changed mind on these items' If you have the put the wrong address in as well please just let me know where you'd like it sending instead of putting in a cancellation as these affect my seller ratings.If you have any questions please askI also do not accept returns on these for any reason. Before you leave negative or neutral feedback for whatever reason please message me first as I will be able to help you with whatever the problem might be.U.S.A Customers Please Read this - If you are worried about the Import tariff on this item the tariffs do not apply to Letters, only parcels and since these are small enough to be classed as a letter you should not be charged a tariff, there is a change it might happen if the delivery address is a PO box or Post Office so please choose your home address if possible. I don't know if this applied to the latest tax as from February 21st 2026 so please be aware of that, it is not my responsibility to pay the tax, it is yours as the buyer. I do not accept returns or cancellations for these reasons.These are printed using a laser-printer with either white ink or a white underlay to make the icons show up over darker basecoats, due to this process there may be small dots or 'speckles' on the colours this is normal for this type of printing process which differs from the types of decals typically found in other miniature kits which are printed on a larger industrial scale.There may also be a slight white offset under the design, this is uncommon but can still happen so please be aware of this as well and the white is not as bright as the official GW sheets as this is not an industrial scale printing process so they may be some slight transparency to the design which lends it's self to a more natural white look anyway.Listed is an A6 sheet with several Wolfspear Squad Role and Jarldom iconsPlease note there is a chance some icons on the side of the sheet get cut off during printing, it is not an exact science and I have no control over the process, it is unlikely that it will happen but sometimes it does but there is a lot of icons on the sheet anyway.Due to this unfortunate occasional error and since I can't fix it myself I will post these sheets as they come like this since the other icons are still usable, I will not accept returns or cancellations if this happens and you haven't read this or allow negative feedback, if I was printing them myself I would be happy to help fix it.Message me if you'd like more than more than one special sheet printed as I can do bulk deals!Icon sizes are roughly3 x 4.3mm Diamonds2.7 x 6mm Zig Zags5mm x 6mm Triangles3.5mm Jarldom markingsSquad Roles and Jarldoms sold separatelyThese were printed on clear decal paper and you need to cut around the icon as close as possible to get them onto the shoulders otherwise the film will be too big I also recommend using the Microsol and Microset methodPlease note that not all detail may be printed on smaller icons such as holes on eyes or anything similar due to how toner ink works, they will still of course give the effect of the icon from afar and on a shoulder pad anyway.Recommended Directions for use1: Gloss Varnish the model or the area you would like to apply the transfer ( I use either Army Painter Gloss Varnish via brush or Hycote Clear Lacquer for spray)2: Wait for the Varnish to dry3: Cut around the decal as close as you can giving your self an edge around the icon (Do not cut the icon) these are not pre cut like regular transfers.4: Apply a thincoat of Microset to the area of the model you will apply the decal5: Soak the transfer in some lukewarm water for a few seconds6: Slide the icon off the paper and onto the model