Radio Wireless Remote Control Shutter Release for Canon EOS Rebel T7 T6 T5 EOS R

Radio Wireless Connection: It works from behind the camera as well as from in front, not having to be in direct line of sight to the camera like an infrared (IR) remote, so it is much more flexible and convenient than IR remote controlCan trigger cameras wireless or wired, wireless range up to 30 meters / 100ft16 possible radio channels, Operate on Radio Frequency 433 MHz, 1 transmitter can trigger multiple receiversCan wirelessly trigger the camera shutter under 5 modes: single shot, unlimited continuous shots, bulb shot, 3 continuous shots and 5 seconds delay shot. (Note: It's not able to control video start and stop)It fits Canon EOS Rebel T7(2000D),Rebel T6(1300D),Rebel T5(1200D),T3(1100D),T3i(600D),T4i(650D),T5i(700D),T6i(750D),T6s(760D), T7i(800D), T8i(850D), SL1(100D), SL2(200D), SL3(250D), XS(1000D), EOS 60D, 60Da, 70D, 77D, 80D, 90D, EOS RP, R, R6, R6 Mark II, R7, R8, R10, R50V, R100, M6, M6 Mark II, M5 and Other Cameras with Sub Mini Connection Product Description This Wireless Remote is designed for cameras that has a remote shutter socket. The system works at a 433MHZ frequency and has 16 available channels. In addition, this wireless remote system adopts a technology to allow the transmitter trigger the receiver without direct line of sight up to 30 meters / 100 ft. Compatible with Select Canon and Pentax Cameras: Canon EOS Rebel T7 / T6 / T5 /T3 / T8i / T7i / T6s / T6i / T5i / T4i / T3i / T2i / T1i / XSi / XS / XTi / SL3 / SL2 / SL1 / EOS R / RP / R6 / R6 Mark II / R7 / R8 / R10 / R50V / R100 / M5 / M6 Mark II / 2000D / 70D / 80D / 90D / 77D / 60D / 60Da / Powershot G16 / G15 / G1X Mark II / G1X Mark III / SX70 HS / SX60 HS (Not for R50 camera)Pentax K30 / K50 / K1 / K3 / K3 II / K5 / K5 II / K5 IIs / K7 / K100D / K100D Super / K10D / K110D / K200D / K20D / K500 / 645D / 645Z Important - How to use: 1. Install the CR-2 battery to the receiver and 23A battery to the transmitter. (Make sure to remove the plastic protective paper on the battery before installation) 2. Set the receiver and transmitter to the same channel (Normally the channel is already matched when you receive the package, so actually you don't need to set it, but if you ever reset the channel, make sure they are the same) 3. Once the batteries are properly installed and the channels are matched, when you press the shutter button on the transmitter, both the LED bulb on the transmitter and receiver will light up. (If not, please check if the battery is installed correctly or the battery is dead) 4. Once the transmitter matches the receiver, connect the receiver to the camera via the camera connecting cable which is included in the package, then set the transmitter into the working mode you want and finally press the shutter button to take a photo wirelessly. Attention Please: This remote does not work when camera is in movie mode, so it cannot control video start and stop! 1/4"-20 Screw Hole on Receiver The 1/4"-20 screw hole on the back of receiver allows you to mount the receiver on tripod or other devices with 1/4"-20 screw when camera without standard hot shoe or hot shoe is occupied. 16 Channels, Easy to Pair This remote works at 433MHZ frequency and has 16 available channels. There are 4 different channel selectors on the back of transmitter and receiver, just need to push the channel selector in the same number and direction to complete the pairing. Package Includes Transmitter x 1 Receiver x 1 CR-2 battery x 1 23A battery x 1 Camera connecting cord x 1